Hello, welcome to Yangzhou Qianglin Hydraulic Machinery Co., Ltd.

24-Hour Hour Hotline:

0514-86602366

0514-86602366

© 2019 Yangzhou Qianglin Hydraulic Machinery Co., Ltd. 苏ICP备18017419号-2 Powered by www.300.cn

HOME         ABOUT         PRODUCT         NEWS         RECRUIT         APPLICATIONS         CONTACT

Fax:0514-86605199       E-mail:yzqljx@163.com       Add:Yangzhou Jiangdu Wujian Industrial Park

Unified Consulting Hotline

NEWS CENTER

Qianglin hydraulics

Introduction of the steps about the base device of the hydraulic cylinder manufacturer

Classification:
Industry news
Release time:
2020/08/20
Page view
[Abstract]:
Hydraulic cylinder manufacturers that, in the installation of hydraulic cylinder time, its base device is also a very important part. Usually, we fix the flange and the base of the head and tail of the hydraulic cylinder together. That is to say, the base can be arranged around the hydraulic cylinder radial, tangential, can also be placed in the axial bottom of the front and rear end. Of course, different device methods are required to meet different device requirements. If it is the method of selecting the radial device, hydraulic cylinder manufacturers think, should ensure that the device surface and Piston rod axis in the same plane. In this case, when the hydraulic cylinder operation, the installation of bolts only accept the shear force. In the case of tangential or axial devices, the appropriate spacing between the shaft of the Piston Rod and the base shall be maintained. In both methods, the bolts of the device are subjected to two forces at the same time, the first being shear, and the other being tortuous forces due to the existence of tipping moments. Hydraulic cylinder manufacturers, by comparison, the tangential device by the tipping moment will be less than the axial device by the tipping moment. Need to pay attention to is, in the installation of the base, we must pay attention to meet the corresponding rules. Hydraulic cylinder manufacturers, for example, if the base of the hydraulic cylinder does not choose the key or pin to accept the shear stress, then the bottom pin fixed bolt should be able to accept all the shear stress, and there is no risk. Hydraulic Cylinder Manufacturers explained that, in fact, if the base device in the front, it is best to use positioning screw or pin to fix. If it is installed in the back end, then can choose loose screw hole, in order to meet the hydraulic cylinder heating, the cylinder can be telescopic requirements.

Hydraulic cylinder manufacturers that, in the installation of hydraulic cylinder time, its base device is also a very important part. Usually, we fix the flange and the base of the head and tail of the hydraulic cylinder together. That is to say, the base can be arranged around the hydraulic cylinder radial, tangential, can also be placed in the axial bottom of the front and rear end. Of course, different device methods are required to meet different device requirements. If it is the method of selecting the radial device, hydraulic cylinder manufacturers think, should ensure that the device surface and Piston rod axis in the same plane. In this case, when the hydraulic cylinder operation, the installation of bolts only accept the shear force. In the case of tangential or axial devices, the appropriate spacing between the shaft of the Piston Rod and the base shall be maintained. In both methods, the bolts of the device are subjected to two forces at the same time, the first being shear, and the other being tortuous forces due to the existence of tipping moments. Hydraulic cylinder manufacturers, by comparison, the tangential device by the tipping moment will be less than the axial device by the tipping moment. Need to pay attention to is, in the installation of the base, we must pay attention to meet the corresponding rules. Hydraulic cylinder manufacturers, for example, if the base of the hydraulic cylinder does not choose the key or pin to accept the shear stress, then the bottom pin fixed bolt should be able to accept all the shear stress, and there is no risk. Hydraulic Cylinder Manufacturers explained that, in fact, if the base device in the front, it is best to use positioning screw or pin to fix. If it is installed in the back end, then can choose loose screw hole, in order to meet the hydraulic cylinder heating, the cylinder can be telescopic requirements.